I do have an option for you but the main variable here is going to be the exact power requirements for the refrigerator. If this is indeed a residential size refrigerator then this would not be practical to run off a small solar panel and battery bank. In order to power a residential size refrigerator you would most likely need around six 6v batteries and a 600+ watt solar system.
If you have no other means of charging you batteries then you would be much better off downsizing your refrigerator... view full answer...
The closest option we have to what you need is the Steel Wiper part # SR66FR which is 30 foot long (can be cut down by 5 feet), is 4-1/16 inches tall, and is tapered with a thickness that starts at 1/8 inch. This is a stick-on application as well. view full answer...
It may very well be possible to rebuild the landing gear on your 2010 Forest River Wildcat 5th wheel with a rebuild kit, but first you will need to identify which model landing gear is installed.
On either of the landing gear legs there should be a part number, this may be on a white sticker or stamped into the metal depending on the specific landing gear. With this part number I can then identify your landing gear and recommend the correct rebuild kit.
If there is not any part numbers... view full answer...
Yes, since we know your 2023 Forest River Wild Cat 290RL has a Lippert chassis the Reese Goose Box part # RP85FR does fit. This is also the only gooseneck adapter that doesn't void the warranty of the chassis either. view full answer...
The Reese Electric 5th Wheel Landing Gear Set # RP500708 has a combined lift capacity of 8,000 pounds for both jacks. This will be enough for your 2008 Forest River Wildcat 5th Wheel. You will be able to control each lifting leg individually to assist with leveling the front of your camper. You will want to verify that the weld stops on your jacks are from inside of top weld stop to inside of bottom weld stop 15-1/2", and between outside of weld stop to outside of weld stop 17-1/2".
I... view full answer...
It's pretty easy to pick out a new panel for a higher rated service, you just need to make sure you get the charge converter size correct. I recommend going with the same size that came with the trailer or was integrated into your old panel since this has more to do with load rather than the supply. That said, if you intend to upgrade your appliances you can go with a higher rated option.
The Progressive Dynamics RV Power Control Center part # PD4560K18LS8 is a good option for a 50 amp... view full answer...
A 6k Dexter axle like what you have has a 3 inch diameter so the Over Under kit part # K71-385-00 that you referenced is correct and would work. You would need to order a quantity of two of these since it is a tandem axle trailer. view full answer...
I sent the picture and info you sent us to Lippert to confirm what pin box you have and they told me it was a Lippert 1621 so the Goose box part # RP85FR that you referenced would be exactly what you'd need. I was also able to confirm that your chassis has a 15.5k capacity so the 20k capacity of this would work well. view full answer...
The Lippert Electric Landing Gear Set part # LC333964 should be an excellent replacement option for a Forest River Wildcat Fifth Wheel. In order to confirm, simply measure the distance between the weld stops and compare that to the dimensions below:
Distance from bottom of upper weld stop to top of lower weld stop: 15-1/2"
Distance from top of upper weld stop to bottom of lower weld stop: 17-1/2"
If yours match, these will be a direct fit. The extra brackets can be discarded. view full answer...
The Correct Track Trailer Alignment and Lift Kit # RR23QX essentially just stacks onto your current hangers to lift your trailer by 1-1/4" or 2-1/4". If you're looking for something that will give you more then there are a few other options available.
Option 1: Cut off your current hangers and have longer ones welded on. This would increase the height based on the increased hanger length.
Option 2: If your axles are above your leaf springs you can use an Over-Under Kit like # K71-385-00... view full answer...
Go To Results